Standard Product Type and Dimensions about Polyimide Tubing

Designation of Product

Model inside diameter(in mm) x Wall thickness(in mm)
(Example: PIT-S 0.5mm x 0.06mm)

Model PIT-FS`(unit : mm)`
Model	Nominal inside diameter	Tolerance of inside diameter	Standard thickness	Standard outside diameter	length
PIT-FS	0.08	±0.009	0.013	0.106	500
	0.09	±0.009	0.013	0.116
	0.10	±0.009	0.013	0.126
	0.11	±0.009	0.02	0.15
	0.12	±0.009	0.02	0.16
	0.13	±0.009	0.02	0.17
	0.14	±0.009	0.02	0.18
	0.15	±0.009	0.02	0.19
	0.16	±0.009	0.02	0.20
	0.17	±0.009	0.02	0.21
	0.18	±0.009	0.02	0.22
	0.19	±0.009	0.02	0.23
	0.20	±0.009	0.02	0.24
	0.23	±0.009	0.02	0.27
	0.25	±0.009	0.02	0.29
	0.30	±0.009	0.02	0.34
	0.32	±0.009	0.02	0.36
	0.45	±0.009	0.02	0.49

Model PIT-S`(unit : mm)`
Model	Nominal inside diameter	Tolerance of inside diameter	Standard thickness	Standard outside diameter	length
PIT-S	0.20	±0.03	0.04	0.28	1000
	0.25	±0.03	0.04	0.33
	0.30	±0.03	0.04	0.38
	0.35	±0.03	0.04	0.43
	0.4	±0.03	0.04, 0.06, 0.08	0.48 ^{(Note 1)}
	0.5	±0.04	0.04, 0.06, 0.08	0.62 ^{(Note 2)}
	0.6	±0.04	0.04, 0.06, 0.08	0.7 ^{(Note 2)}
	0.7	±0.04	0.06	0.82
	0.8	±0.05	0.04, 0.06, 0.08	0.92 ^{(Note 2)}
	0.9	±0.05	0.06	1.02
	1.0	±0.06	0.04, 0.06, 0.08	1.12 ^{(Note 2)}
	1.1	±0.06	0.06	1.22
	1.2	±0.06	0.06	1.32
	1.3	±0.06	0.06	1.42
	1.4	±0.06	0.06	1.52
	1.5	±0.06	0.06	1.62
	1.6	±0.08	0.06	1.72
	1.7	±0.08	0.06	1.82
	1.8	±0.08	0.06	1.92
	1.9	±0.08	0.06	2.02
	2.0	±0.10	0.06	2.12

(Note 1)Wall Thickness at 0.04mmBack to Main Content

(Note 2)Wall Thickness at 0.06mmBack to Main Content

Model PIT-LS`(unit : mm)`
Model	Nominal inside diameter	Tolerance of inside diameter	Standard thickness	Standard outside diameter	length
PIT-LS	2.5	±0.10	0.06	2.62	1000
PIT-LS	3.0	±0.10	0.06	3.12	1000

Sub Category Menu starts

Sub Category Menu ends

End of page