*また、INFONET-RX30による専用線を用いたインターネット接続(1.5Mbps)も可能です。ここでは、INFONET 3780での設定例を挙げます。
INFONET 3780N Remote Brouter B V01.26 1996.11.26 WAN topology (--) 1997/08/05 11:25:57 ( 0 00:07:59) Super Mode 1. configuration display 2. configuration set (normal) 3. configuration set (expert) 4. operation 5. information 6. shift to super mode 7. exit from remote console or current mode Select the number. : 2 *** Selecting PORT way *** 1 HSD 2 FR Select the number. []:1 ←専用線を使用します Execute system reset. Do you want to continue ? [y/n] y << ここで一度リセットがかかります >> INFONET 3780N Remote Brouter B V01.26 1996.11.26 WAN topology (1) 1997/08/05 11:27:17 ( 0 00:00:11) Normal Mode 1. configuration display 2. configuration set (normal) 3. configuration set (expert) 4. operation 5. information 6. shift to super mode 7. exit from remote console or current mode Select the number. : 6 ←Super Modeに入ります Password: INFONET 3780N Remote Brouter A V01.26 1996.11.26 WAN topology (1) 1997/08/05 11:27:27 ( 0 00:00:20) Super Mode 1. configuration display 2. configuration set (normal) 3. configuration set (expert) 4. operation 5. information 6. shift to super mode 7. exit from remote console or current mode Select the number. : 2 *** Selecting PORT way *** * 1 HSD 2 FR Select the number. [1]: ←専用線を使用します : :省略 : *** Main: Set HSD configuration *** <Main HSD parameter(s)> speed : 1.5Mbps ←回線速度は1.5Mbps Do you change (y/n)? [n]: *** Set basic configuration *** <Basic configuration parameter(s)> IP routing : not use IP filtering : not use IPX routing : not use bridging : not use SNMP : use Do you change (y/n)? [n]: y IP routing (1:use 2:not use) [2]: 1 ←IPルーティングを行います IP filtering (1:use 2:not use) [2]: IPX routing (1:use 2:not use) [2]: bridging (1:use 2:not use) [2]: SNMP (1:use 2:not use) [1]: 2 Basic parameter(s) are set to the following values. <Basic configuration parameter(s)> IP routing : use IP filtering : not use IPX routing : not use bridging : not use SNMP : not use Set OK (y/n)? [y]: *** Set IP router configuration *** <IP router configuration parameter(s)> routing interface list broadcast or IP address subnetmask remote address interface type -------+----------------+----------------+----------------+------ LAN 0.0.0.0 0.0.0.0 0.0.0.0 broadcast HSD point to point Do you change (y/n)? [n]: y LAN IP address []: 158.***.100.1 ←ルータのLANアドレス (プロバイダから与えられたグローバルアドレスの1つ) subnetmask [255.255.255.0]: 255.255.255.240 ←プロバイダで指示されたサブネットマスク broadcast [158.***.100.15]: ←リターンのみ(自動的に値が入ります) HSD interface type (1:broadcast 2:point to point) [2]: IP address []: remote IP address []:192.168.1.1 ←ダミーのアドレス(LAN側で使われていないアドレスを使用する) remote subnetmask [255.255.255.0]: IP router parameter(s) are set to the following values. <IP router configuration parameter(s)> routing interface list broadcast or IP address subnetmask remote address interface type -------+----------------+----------------+----------------+------ LAN 158.***.100.1 255.255.255.240 158.***.100.15 broadcast HSD 255.255.255.0 192.168.1.1 point to point Set OK (y/n)? [y]: *** Set IP static routing configuration *** 1. change 2. delete 3. add 4. display 5. end Select the number. [5]:3 ←スタティックルートを設定します <add IP static routing data> destination address [0.0.0.0]: mask [0.0.0.0]: gateway [0.0.0.0]:192.168.1.1 ←HSDのアドレスと同じアドレスを設定 metric [16]: preference [50]: IP static routing date: no dst address mask gateway metric preference -------+----------------+----------------+----------------+------ 1 0.0.0.0 ---.---.---.--- 192.168.1.1 16 50 Set OK (y/n)? [y]: : :省略 : (Warning): Some configurations are not updated unless you reset 1. Save new parameter(s) and reset 3. Configurations set again 2. Save new parameter(s) only 4. Quit (no save and no reset) Select the number. : 2 基本設定を終了し、拡張設定に入ります。 [メインメニュー]の[3. configuration set (expert)]から[4. IP routing] を選択し、[2. RIP interface]を設定します。 *** EXP.: Set RIP(IP) interface configuration *** <RIP(IP) interface parameter(s)> send recv metric preference control control -------+----------------+----------------+----------------+---- LAN on on 1 0 HSD on on 0 0 Do you change (y/n)? [n]:y LAN send control(1.on 2.off)[1]: recv control(1.on 2.off)[1]: metric[1]: preference[0]: HSD send control81.on 2.off)[1]:2 ←RIPを使用しません recv control(1.on 2.off)[1]:2 ←RIPを使用しません metric[0]: preference[0]: RIP(IP) interface farameter(s) are set to the following walues <RIP(IP) interface parameter(s)> send recv metric preference control control -------+----------------+----------------+----------------+---- LAN on on 1 0 HSD off off 0 0 Set OK (y/n)?[y]: [ESC]キーをおし、メインメニューへ戻る [メインメニュー]の[4.operation]から[reset]を起動し、Normal Resetを 実施することで設定された内容が有効となります。