インタフェースアドレスは、InverseARPにより、互いに自動的に割り付けられます。各フレームリレー回線の回線速度は128kbps、CIR値は16kbpsとします。
*ここでは、INFONET-RX20での設定例を挙げます。INFONET-RX10Hでの設定例はこちら。
INFONET-RX20 Remote Router B V01.03 1998.04.15 WAN topology ( 6) 1998/07/01 15:36:10 ( 0 00:14:10) Normal Mode 1. configuration display 2. configuration set (normal) 3. configuration set (expert) 4. operation 5. information 6. shift to super mode 7. exit from remote console or current mode Select the number. : 6 ←Super Modeに移動します New password: ←必ずパスワードを入れてください Retype New password: New password is accepted. INFONET-RX20 Remote Router B V01.03 1998.04.15 WAN topology ( 6) 1998/07/01 15:36:14 ( 0 00:14:14) Super Mode 1. configuration display 2. configuration set (normal) 3. configuration set (expert) 4. operation 5. information 6. shift to super mode 7. exit from remote console or current mode Select the number. : 2 *** Selecting PORT way *** 1 HSD, HSD * 2 HSD, ISDN 3 FR, ISDN Select the number. [2]: 3 ←フレームリレーを選択します Execute system reset. Do you want to continue ? [y/n] y << ここでリセットが入ります >> INFONET-RX20 Remote Router B V01.03 1998.04.15 WAN topology (--) 1998/07/01 15:37:39 ( 0 00:00:03) Normal Mode 1. configuration display 2. configuration set (normal) 3. configuration set (expert) 4. operation 5. information 6. shift to super mode 7. exit from remote console or current mode Select the number. : 6 Password: INFONET-RX20 Remote Router B V01.03 1998.04.15 WAN topology (--) 1998/07/01 15:37:43 ( 0 00:00:08) Super Mode 1. configuration display 2. configuration set (normal) 3. configuration set (expert) 4. operation 5. information 6. shift to super mode 7. exit from remote console or current mode Select the number. : 2 *** Selecting PORT way *** 1 HSD, HSD 2 HSD, ISDN * 3 FR, ISDN Select the number. [3]: *** Set current time parameter(s) *** 1998/07/01 15:37:46 Do you change (y/n)? [n]: *** Set Default host name configuration *** <Default host name configuration parameter(s)> host name : password : Do you change (y/n)? [n]: *** Selecting WAN topology *** <"L:" is load split> 1 FR 2 FR, ( B:ISDN#1) 3 FR, ( B:ISDN#1,2) 4 ISDN#1 5 ISDN#1 (L :ISDN#2) 6 FR, ISDN#1 7 FR, ISDN#1 (L :ISDN#2) 8 ISDN#1, ISDN#2 9 FR, ISDN#1, ISDN#2 Select the number. [1]: ←フレームリレー1回線を使用します *** Main: Set FR configuration *** <Main FR parameter(s)> speed : 0Kbps Do you change (y/n)? [n]: y speed(1:64K 2:128K) [2]: ←回線速度は128kbps Main FR parameter(s) are set to the following values. <Main FR parameter(s)> speed : 128Kbps Set OK (y/n)? [y]: *** Set DLCI(CIR) table configuration *** 1. change 2. display 3. end Select the number. [3]: 2 Select the DLCI number. [all]: <DLCI(CIR) table (max 32 entries)> DLCI CIR(bps) data compress -----+--------+------------- 16 64000 no 17 64000 no 18 64000 no 19 64000 no 20 64000 no 21 64000 no 22 64000 no - MORE - *** Set DLCI(CIR) table configuration *** 1. change 2. display 3. end Select the number. [3]: 1 ←契約しているCIR値に変更します <Change DLCI(CIR) data> Select the DLCI number. : 16 ←契約しているDLCI番号を選択する Selected DLCI(CIR) data: DLCI CIR(bps) data compress -----+--------+------------- 16 64000 no CIR (bps) [64000]: 16000 ←CIR値は16000bps data compress (1:yes 2:no) [2]: DLCI(CIR) data: DLCI CIR(bps) data compress -----+--------+------------- 16 16000 no Change OK (y/n)? [y]: << 同様にDLCI 17〜19を設定 >> *** Set DLCI(CIR) table configuration *** 1. change 2. display 3. end Select the number. [3]: *** Set basic configuration *** <Basic configuration parameter(s)> IP routing : use IP filtering : not use IPX routing : not use AppleTalk routing: not use bridging : not use SNMP : use Do you change (y/n)? [n]: *** Set IP router configuration *** <IP router configuration parameter(s)> routing interface list broadcast or IP address subnetmask remote address interface type -------+----------------+----------------+----------------+-------------- LAN 192.52.150.1 255.255.255.0 192.52.150.255 broadcast FR point to point OSPF protocol: not use Do you change (y/n)? [n]: y LAN IP address [192.52.150.1]: 192.168.1.1 ←ルータのLANアドレス subnetmask [255.255.255.0]: broadcast [192.168.1.255]: FR interface type (1:broadcast 2:point to point) [2]: ←Unnumberedで接続 OSPF protocol (1:use 2:not use) [2]: IP router parameter(s) are set to the following values. <IP router configuration parameter(s)> routing interface list broadcast or IP address subnetmask remote address interface type -------+----------------+----------------+----------------+-------------- LAN 192.168.1.1 255.255.255.0 192.168.1.255 broadcast FR point to point OSPF protocol: not use Set OK (y/n)? [y]: *** Set RIP(IP) motion configuration *** <RIP(IP) motion parameter(s)> mode : supplier default metric: 16 Do you change (y/n)? [n]: *** Set RIP(IP) interface configuration *** <RIP(IP) interface parameter(s)> send recv metric pre- broad- interval ageout time control control ference cast (sec) (sec) ------+-------+-------+------+-------+------+----------+------+---------- LAN RIP1 RIP1,2 0 0 - - - - FR RIP1 RIP1,2 0 0 off 30 off 180 <RIP2 password> LAN : (not configured) FR : (not configured) Do you change (y/n)? [n]: y LAN RIP send control (1:RIP1 2:RIP2 3:RIP1,2 4:off) [1]: recv control (1:RIP1 2:RIP2 3:RIP1,2 4:off) [3]: password []: metric [0]: preference [0]: FR RIP send control (1:RIP1 2:RIP2 3:RIP1,2 4:off) [1]: 4 ←RIPを使用しません recv control (1:RIP1 2:RIP2 3:RIP1,2 4:off) [3]: 4 ←RIPを使用しません metric [0]: preference [0]: broadcast (1:on 2:off) [2]: broadcast interval (sec) [30]: RIP entry ageout (1:on 2:off) [2]: ageout time (sec) [180]: RIP(IP) interface parameter(s) are set to the following values. <RIP(IP) interface parameter(s)> send recv metric pre- broad- interval ageout time control control ference cast (sec) (sec) ------+-------+-------+------+-------+------+----------+------+---------- LAN RIP1 RIP1,2 0 0 - - - - FR off off 0 0 off 30 off 180 <RIP2 password> LAN : (not configured) FR : Set OK (y/n)? [y]: **** Set IP static routing configuration *** 1. change 2. delete 3. add 4. display 5. end Select the number. [5]: 4 <IP static routing table (max 32 entries)> no dst address mask metric preference gateway ---+---------------+---------------+------+---------- 1. 0.0.0.0 ---.---.---.--- 16 50 ISDN#1 *** Set IP static routing configuration *** 1. change 2. delete 3. add 4. display 5. end Select the number. [5]: 2 ←必要でないスタティックルートを削除する <Delete IP static routing data> Select the entry number. : 1 Selected IP static routing data: no dst address mask metric preference gateway ---+---------------+---------------+------+---------- 1. 0.0.0.0 ---.---.---.--- 16 50 ISDN#1 Delete OK (y/n)? [n]: y *** Set IP static routing configuration *** 1. change 2. delete 3. add 4. display 5. end Select the number. [5]: 3 ←スタティックルートを設定する <Add IP static routing data> destination address [0.0.0.0]: 192.168.2.0 mask [255.255.255.0]: gateway [0.0.0.0]: 192.168.2.1 metric [16]: 2 preference [50]: IP static routing data: no dst address mask metric preference gateway ---+---------------+---------------+------+---------- 1. 192.168.2.0 255.255.255.0 2 50 192.168.2.1 Add OK (y/n)? [y]: << 同様に〜192.168.5.0宛のスタティックルートを設定 >> *** Set IP static routing configuration *** 1. change 2. delete 3. add 4. display 5. end Select the number. [5]: : :省略 : Now you have set all configurations! Do you display the configurations (y/n)? [y]: n (Warning): Some configurations are not updated unless you reset 1. Save new parameter(s) and reset 3. Configurations set again 2. Save new parameter(s) only 4. Quit (no save and no reset) Select the number. : 2 ←セーブを行います INFONET-RX20 Remote Router B V01.03 1998.04.15 WAN topology ( 1) 1998/07/01 15:40:45 ( 0 00:03:10) Super Mode 1. configuration display 2. configuration set (normal) 3. configuration set (expert) 4. operation 5. information 6. shift to super mode 7. exit from remote console or current mode Select the number. : 3 ←拡張設定を行います *** Expert mode (configuration) menu *** 1. datalink 2. bridging : :省略 : Select the number. : 1 *** EXP.: Set datalink configuration *** 1. datalink 2. DLCI address table 3. DLCI(CIR) table 4. DLCI protocol table Select the number. : 3 *** EXP.: Set datalink DLCI(CIR) table configuration *** 1. change 2. display 3. end Select the number. [3]: 1 <Change datalink DLCI(CIR) data> Select the DLCI number. : 16 Selected datalink DLCI(CIR) data: DLCI CIR(bps) PIR(bps) lowspeed(bps) -----+--------+--------+------------- 16 16000 64000 0 CIR (bps) [16000]: PIR (bps) [64000]: 128000 ←回線速度を設定します lowspeed (bps) [0]: datalink DLCI(CIR) data: DLCI CIR(bps) PIR(bps) lowspeed(bps) -----+--------+--------+------------- 16 16000 128000 0 Change OK (y/n)? [y]: << 同様にDLCI 17〜19を設定 >> *** EXP.: Set datalink DLCI(CIR) table configuration *** 1. change 2. display 3. end Select the number. [3]: 2 Select the DLCI number. [all]: <Datalink DLCI(CIR) table (max 32 entries)> DLCI CIR(bps) PIR(bps) lowspeed(bps) -----+--------+--------+------------- 16 16000 128000 0 17 16000 128000 0 18 16000 128000 0 19 16000 128000 0 20 64000 64000 0 21 64000 64000 0 22 64000 64000 0 - MORE - *** EXP.: Set datalink DLCI(CIR) table configuration *** 1. change 2. display 3. end Select the number. [3]: *** EXP.: Set datalink configuration *** 1. datalink 2. DLCI address table 3. DLCI(CIR) table 4. DLCI protocol table Select the number. : << ESCでメインメニューまで戻る >> INFONET-RX20 Remote Router B V01.03 1998.04.15 WAN topology ( 1) 1998/07/01 15:42:15 ( 0 00:04:39) Super Mode 1. configuration display 2. configuration set (normal) 3. configuration set (expert) 4. operation 5. information 6. shift to super mode 7. exit from remote console or current mode Select the number. : 4 *** Operation menu *** 1. connect ISDN#1 main line 2. connect ISDN#2 main line : :省略 : 17. reset Select the number. : 17 *** Reset *** 1. normal restart 2. all default restart 3. limited default restart Reset mode: 1 ←リセットが行われ立ち上がり後、設定が有効です
INFONET-RX20 Remote Router B V01.03 1998.04.15 WAN topology ( 6) 1998/07/01 15:36:10 ( 0 00:14:10) Normal Mode 1. configuration display 2. configuration set (normal) 3. configuration set (expert) 4. operation 5. information 6. shift to super mode 7. exit from remote console or current mode Select the number. : 6 ←Super Modeに移動します New password: ←必ずパスワードを入れてください Retype New password: New password is accepted. INFONET-RX20 Remote Router B V01.03 1998.04.15 WAN topology ( 6) 1998/07/01 15:36:14 ( 0 00:14:14) Super Mode 1. configuration display 2. configuration set (normal) 3. configuration set (expert) 4. operation 5. information 6. shift to super mode 7. exit from remote console or current mode Select the number. : 2 *** Selecting PORT way *** 1 HSD, HSD * 2 HSD, ISDN 3 FR, ISDN Select the number. [2]: 3 ←フレームリレーを選択します Execute system reset. Do you want to continue ? [y/n] y << ここでリセットが入ります >> INFONET-RX20 Remote Router B V01.03 1998.04.15 WAN topology (--) 1998/07/01 15:37:39 ( 0 00:00:03) Normal Mode 1. configuration display 2. configuration set (normal) 3. configuration set (expert) 4. operation 5. information 6. shift to super mode 7. exit from remote console or current mode Select the number. : 6 Password: INFONET-RX20 Remote Router B V01.03 1998.04.15 WAN topology (--) 1998/07/01 15:37:43 ( 0 00:00:08) Super Mode 1. configuration display 2. configuration set (normal) 3. configuration set (expert) 4. operation 5. information 6. shift to super mode 7. exit from remote console or current mode Select the number. : 2 *** Selecting PORT way *** 1 HSD, HSD 2 HSD, ISDN * 3 FR, ISDN Select the number. [3]: *** Set current time parameter(s) *** 1998/07/01 15:37:46 Do you change (y/n)? [n]: *** Set Default host name configuration *** <Default host name configuration parameter(s)> host name : password : Do you change (y/n)? [n]: *** Selecting WAN topology *** <"L:" is load split> 1 FR 2 FR, ( B:ISDN#1) 3 FR, ( B:ISDN#1,2) 4 ISDN#1 5 ISDN#1 (L :ISDN#2) 6 FR, ISDN#1 7 FR, ISDN#1 (L :ISDN#2) 8 ISDN#1, ISDN#2 9 FR, ISDN#1, ISDN#2 Select the number. [1]: ←フレームリレー1回線を使用します *** Main: Set FR configuration *** <Main FR parameter(s)> speed : 0Kbps Do you change (y/n)? [n]: y speed(1:64K 2:128K) [2]: ←回線速度は128kbps Main FR parameter(s) are set to the following values. <Main FR parameter(s)> speed : 128Kbps Set OK (y/n)? [y]: *** Set DLCI(CIR) table configuration *** 1. change 2. display 3. end Select the number. [3]: 2 Select the DLCI number. [all]: <DLCI(CIR) table (max 32 entries)> DLCI CIR(bps) data compress -----+--------+------------- 16 64000 no 17 64000 no 18 64000 no 19 64000 no 20 64000 no 21 64000 no 22 64000 no - MORE - *** Set DLCI(CIR) table configuration *** 1. change 2. display 3. end Select the number. [3]: 1 ←契約しているCIR値に変更します <Change DLCI(CIR) data> Select the DLCI number. : 16 ←契約しているDLCI番号を選択する Selected DLCI(CIR) data: DLCI CIR(bps) data compress -----+--------+------------- 16 64000 no CIR (bps) [64000]: 16000 ←CIR値は16000bps data compress (1:yes 2:no) [2]: DLCI(CIR) data: DLCI CIR(bps) data compress -----+--------+------------- 16 16000 no Change OK (y/n)? [y]: *** Set DLCI(CIR) table configuration *** 1. change 2. display 3. end Select the number. [3]: *** Set basic configuration *** <Basic configuration parameter(s)> IP routing : use IP filtering : not use IPX routing : not use AppleTalk routing: not use bridging : not use SNMP : use Do you change (y/n)? [n]: *** Set IP router configuration *** <IP router configuration parameter(s)> routing interface list broadcast or IP address subnetmask remote address interface type -------+----------------+----------------+----------------+-------------- LAN 192.52.150.1 255.255.255.0 192.52.150.255 broadcast FR point to point OSPF protocol: not use Do you change (y/n)? [n]: y LAN IP address [192.52.150.1]: 192.168.2.1 ←ルータのLANアドレス subnetmask [255.255.255.0]: broadcast [192.168.2.255]: FR interface type (1:broadcast 2:point to point) [2]: ←Unnumberedで接続 OSPF protocol (1:use 2:not use) [2]: IP router parameter(s) are set to the following values. <IP router configuration parameter(s)> routing interface list broadcast or IP address subnetmask remote address interface type -------+----------------+----------------+----------------+-------------- LAN 192.168.2.1 255.255.255.0 192.168.2.255 broadcast FR point to point OSPF protocol: not use Set OK (y/n)? [y]: *** Set RIP(IP) motion configuration *** <RIP(IP) motion parameter(s)> mode : supplier default metric: 16 Do you change (y/n)? [n]: *** Set RIP(IP) interface configuration *** <RIP(IP) interface parameter(s)> send recv metric pre- broad- interval ageout time control control ference cast (sec) (sec) ------+-------+-------+------+-------+------+----------+------+---------- LAN RIP1 RIP1,2 0 0 - - - - FR RIP1 RIP1,2 0 0 off 30 off 180 <RIP2 password> LAN : (not configured) FR : (not configured) Do you change (y/n)? [n]: y LAN RIP send control (1:RIP1 2:RIP2 3:RIP1,2 4:off) [1]: recv control (1:RIP1 2:RIP2 3:RIP1,2 4:off) [3]: password []: metric [0]: preference [0]: FR RIP send control (1:RIP1 2:RIP2 3:RIP1,2 4:off) [1]: 4 ←RIPを使用しません recv control (1:RIP1 2:RIP2 3:RIP1,2 4:off) [3]: 4 ←RIPを使用しません metric [0]: preference [0]: broadcast (1:on 2:off) [2]: broadcast interval (sec) [30]: RIP entry ageout (1:on 2:off) [2]: ageout time (sec) [180]: RIP(IP) interface parameter(s) are set to the following values. <RIP(IP) interface parameter(s)> send recv metric pre- broad- interval ageout time control control ference cast (sec) (sec) ------+-------+-------+------+-------+------+----------+------+---------- LAN RIP1 RIP1,2 0 0 - - - - FR off off 0 0 off 30 off 180 <RIP2 password> LAN : (not configured) FR : Set OK (y/n)? [y]: **** Set IP static routing configuration *** 1. change 2. delete 3. add 4. display 5. end Select the number. [5]: 4 <IP static routing table (max 32 entries)> no dst address mask metric preference gateway ---+---------------+---------------+------+---------- 1. 0.0.0.0 ---.---.---.--- 16 50 ISDN#1 *** Set IP static routing configuration *** 1. change 2. delete 3. add 4. display 5. end Select the number. [5]: 2 ←必要でないスタティックルートを削除する <Delete IP static routing data> Select the entry number. : 1 Selected IP static routing data: no dst address mask metric preference gateway ---+---------------+---------------+------+---------- 1. 0.0.0.0 ---.---.---.--- 16 50 ISDN#1 Delete OK (y/n)? [n]: y *** Set IP static routing configuration *** 1. change 2. delete 3. add 4. display 5. end Select the number. [5]: 3 ←スタティックルートを設定する <Add IP static routing data> destination address [0.0.0.0]: 192.168.1.0 mask [255.255.255.0]: gateway [0.0.0.0]: 192.168.1.1 metric [16]: 2 preference [50]: IP static routing data: no dst address mask metric preference gateway ---+---------------+---------------+------+---------- 1. 192.168.1.0 255.255.255.0 2 50 192.168.1.1 Add OK (y/n)? [y]: (通信したい相手のみを設定) << 同様に〜192.168.5.0宛のスタティックルートを設定 >> *** Set IP static routing configuration *** 1. change 2. delete 3. add 4. display 5. end Select the number. [5]: : :省略 : Now you have set all configurations! Do you display the configurations (y/n)? [y]: n (Warning): Some configurations are not updated unless you reset 1. Save new parameter(s) and reset 3. Configurations set again 2. Save new parameter(s) only 4. Quit (no save and no reset) Select the number. : 2 ←セーブを行います INFONET-RX20 Remote Router B V01.03 1998.04.15 WAN topology ( 1) 1998/07/01 15:40:45 ( 0 00:03:10) Super Mode 1. configuration display 2. configuration set (normal) 3. configuration set (expert) 4. operation 5. information 6. shift to super mode 7. exit from remote console or current mode Select the number. : 3 ←拡張設定を行います *** Expert mode (configuration) menu *** 1. datalink 2. bridging : :省略 : Select the number. : 1 *** EXP.: Set datalink configuration *** 1. datalink 2. DLCI address table 3. DLCI(CIR) table 4. DLCI protocol table Select the number. : 3 *** EXP.: Set datalink DLCI(CIR) table configuration *** 1. change 2. display 3. end Select the number. [3]: 1 <Change datalink DLCI(CIR) data> Select the DLCI number. : 16 Selected datalink DLCI(CIR) data: DLCI CIR(bps) PIR(bps) lowspeed(bps) -----+--------+--------+------------- 16 16000 64000 0 CIR (bps) [16000]: PIR (bps) [64000]: 128000 ←回線速度を設定します lowspeed (bps) [0]: datalink DLCI(CIR) data: DLCI CIR(bps) PIR(bps) lowspeed(bps) -----+--------+--------+------------- 16 16000 128000 0 Change OK (y/n)? [y]: *** EXP.: Set datalink DLCI(CIR) table configuration *** 1. change 2. display 3. end Select the number. [3]: 2 Select the DLCI number. [all]: <Datalink DLCI(CIR) table (max 32 entries)> DLCI CIR(bps) PIR(bps) lowspeed(bps) -----+--------+--------+------------- 16 16000 128000 0 17 64000 64000 0 18 64000 64000 0 19 64000 64000 0 20 64000 64000 0 21 64000 64000 0 22 64000 64000 0 - MORE - *** EXP.: Set datalink DLCI(CIR) table configuration *** 1. change 2. display 3. end Select the number. [3]: *** EXP.: Set datalink configuration *** 1. datalink 2. DLCI address table 3. DLCI(CIR) table 4. DLCI protocol table Select the number. : << ESCでメインメニューまで戻る >> INFONET-RX20 Remote Router B V01.03 1998.04.15 WAN topology ( 1) 1998/07/01 15:42:15 ( 0 00:04:39) Super Mode 1. configuration display 2. configuration set (normal) 3. configuration set (expert) 4. operation 5. information 6. shift to super mode 7. exit from remote console or current mode Select the number. : 4 *** Operation menu *** 1. connect ISDN#1 main line 2. connect ISDN#2 main line : :省略 : 17. reset Select the number. : 17 *** Reset *** 1. normal restart 2. all default restart 3. limited default restart Reset mode: 1 ←リセットが行われ立ち上がり後、設定が有効です